11 products
11 products
Spalter Brush (Bristle, Nylon) | GLZ-07
GLZ-07_Size040
Regular price $10.15 Sale price $8.12 Save $2.03/
Shipping calculated at checkout.
The spalter is one of the most used tools in our decorative brush kit. Unlike the average cheap brush, our spalter has a thick row (1/3 inch) of short hair that is densely packed with a bristle/nylon blend for ultimate performance and control for today's water mediums. The smaller sizes have a variety of uses, from basecoats to final glazing, 'stretching' to softening. Available in 8 sizes. Amazing for entire wall strie or criss-cross.
- Nylon synthetic fiber with 50% natural bristle
- stretch glaze for ultimate consistency
- Softens unwanted brush/roller marks
- Excellent for applying thin varnish and waxes
- Fine/subtle strie
- Water - Wash with soap, Oil: Thinned & wash w/ soap
SIZE TRANSLATIONS
| SIZE | BRUSH LENGTH | FERRULE WIDTH | FERRULE LENGTH |
HAIR LENGTH |
| 40 |
6.9" / 17.6cm |
.4" / 9mm | 1.6" / 40mm | 1.4" / 36mm |
| 60 |
7.5" / 19cm |
.4" / 9mm | 2.4" / 60mm | 1.4" / 36mm |
| 80 | 7.6" / 19.3cm | .4" / 9mm | 3.1" / 80mm | 1.4" / 36mm |
| 100 | 8.3" / 21cm | .4" / 9mm | 4" / 100mm | 1.6" / 41mm |
| 150 | 8.8" / 22.4cm | .4" / 9mm | 6" / 150mm | 1.8" / 46mm |
| 200 | 9.7" / 24.7cm | .4" / 9mm | 8" / 200mm | 1.9" / 47mm |
| 250 | 9.5" / 24.2cm | .4" / 9mm | 9.9" / 250mm | 1.8" / 46mm |
| 300 | 9.6" / 24.3cm | .4" / 9mm | 11.8" / 300mm | 1.7" / 44mm |
BRUSH SPECIFICATIONS
|
HAIR TYPE |
Natural Bristle / Nylon blend |
|
BRUSH HOLD |
Drummer's Hold, "Quack Motion" |
|
USAGE |
Soften roller marks on base coat & varnish applications; Moire |
|
MEDIUM |
Water or Oil |
|
FERRULE |
Copper |
|
HANDLE |
Wooden flat short |
How-To Brush Care Guide
Prepare your brushes for their first use - read below.
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
- Wash the brush thoroughly with a mild dish soap in warm water and massage the hair to comb out the loose bristles. Rinse until there is no soap residue left in the brush.
- Ring the brush out by rolling it between your hands as if you were trying to make a fire with a stick to fluff out the brush.
- Let dry by hanging the brushes or lay it down at the edge of a table (a hog bristle will have a strong odor due to the bone glue used to attach the bristles. This will go away after a few washings.)
Repeat this process a few more times.
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
Proper cleaning procedure
for oil/water and large or small brushes:
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
Tooth Spalter Brush (Bristle, Nylon) | GLZ-08
GLZ-08_Size-040
Regular price $11.75 Sale price $9.40 Save $2.35/
Shipping calculated at checkout.
Our tooth spalter has "teeth" cut out of a traditional spalter. These spaces allow for the brush to be used for different applications. This model mimics our traditional spalter shape and standard length. This brush is typically used to manipulate painting mediums such as glaze and paint by displacing medium. It can also be dipped into medium to create a print. The tooth spalter creates clear, strie lines with a series of parallel lines.
- Uses: Strie, general glazing, dry-brushing, straight graining (side grains) in woodgraining, use with thick paint or textures.
- Teeth are machine cut but meant to be randomly spaced. Generally, the teeth gaps are 3-4mm (.15") wide.
- Smaller sizes are great for window and door casing. Larger sizes for entire walls.
- hand-picked for a superior tip
- Brush tips are manufactured to flower to hold more paint which will allow the brush to cut sharp edges.
SIZE TRANSLATIONS
| SIZE | BRUSH LENGTH | FERRULE WIDTH | FERRULE LENGTH |
HAIR LENGTH |
| 40 | 6.9" / 17.6cm | .4" / 9mm | 1.6" / 40mm | 1.5" / 37mm |
| 60 | 7.2" / 18.4cm | .4" / 9mm | 2.4" / 60mm | 1.6" / 40mm |
| 80 |
7.6" / 19.4cm |
.4" / 9mm | 3.1" / 80mm | 1.4" / 36mm |
| 100 |
8.2" / 20.9cm |
.4" / 10mm | 4" / 100mm | 1.7" / 42mm |
| 150 |
8.8" / 22.3cm |
.4" / 10mm | 6" / 150mm | 1.9" / 47mm |
| 200 | 9.8" / 24.8cm | .4" / 10mm | 8" / 200mm | 2.1" / 54mm |
BRUSH SPECIFICATIONS
|
HAIR TYPE |
Natural Bristle / Nylon blend |
|
BRUSH HOLD |
Drummer's Hold |
|
USAGE |
Strie; straight graining in wood |
|
MEDIUM |
Water or Oil |
|
FERRULE |
Copper |
|
HANDLE |
Wooden flat short |
How-To Brush Care Guide
Prepare your brushes for their first use - read below.
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
- Wash the brush thoroughly with a mild dish soap in warm water and massage the hair to comb out the loose bristles. Rinse until there is no soap residue left in the brush.
- Ring the brush out by rolling it between your hands as if you were trying to make a fire with a stick to fluff out the brush.
- Let dry by hanging the brushes or lay it down at the edge of a table (a hog bristle will have a strong odor due to the bone glue used to attach the bristles. This will go away after a few washings.)
Repeat this process a few more times.
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
Proper cleaning procedure
for oil/water and large or small brushes:
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
Spalter Brush - Regular (Bluetop) | GLZ-24
GLZ-24_Size-040
Regular price $10.00 Sale price $8.00 Save $2.00/
Shipping calculated at checkout.
Unique blue, silky fiber in our traditional spalter (mottler) shape and standard length (45mm = 1.75"). This brush is primarily used to aid application of varnishes, thinned latex paints, and acrylic glazes. Unlike the "chip" brush that can be found in standard hardware stores, our spalter brush has a thick row of densely packed hair for ultimate performance and control.
SIZE TRANSLATIONS
| SIZE | BRUSH LENGTH | FERRULE WIDTH | FERRULE LENGTH |
HAIR LENGTH |
| 40 |
7.8" / 19.7cm |
.4" / 9mm | 1.6" / 40mm | 1.8" / 45mm |
| 60 | 7.8" / 19.7cm | .4" / 9mm | 2.3" / 60mm |
1.8" / 45mm |
| 80 |
7.8" / 19.7cm |
.4" / 9mm | 3.1" / 80mm |
1.8" / 45mm |
| 100 | 8.9" / 22.5cm | .4" / 9mm | 4" / 100mm |
1.8" / 45mm |
| 150 | 9.1" / 23.1cm | .4" / 9mm | 6" / 150mm |
1.8" / 45mm |
| 200 | 9.6" / 24.5cm | .4" / 9mm | 8" / 200mm |
1.8" / 45mm |
BRUSH SPECIFICATIONS
|
HAIR TYPE |
Bluetop synthetic |
|
USAGE |
Strie; moire; softening paint; varnish |
How-To Brush Care Guide
Prepare your brushes for their first use - read below.
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
- Wash the brush thoroughly with a mild dish soap in warm water and massage the hair to comb out the loose bristles. Rinse until there is no soap residue left in the brush.
- Ring the brush out by rolling it between your hands as if you were trying to make a fire with a stick to fluff out the brush.
- Let dry by hanging the brushes or lay it down at the edge of a table (a hog bristle will have a strong odor due to the bone glue used to attach the bristles. This will go away after a few washings.)
Repeat this process a few more times.
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
Proper cleaning procedure
for oil/water and large or small brushes:
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
4-in-1 Flat Spalter Brush (Bristle) | GLZ-09
GLZ-09
Regular price $39.00/
Shipping calculated at checkout.
Our long haired spalter is a combination of a spalter, softener, and a mini-flogger. This natural bristle brush becomes economical because of it's versatility. Our spalters are over 1/3" thick. From strie to corner stippling, smoothing to moire, this brush does it all. Keep it in your back pocket and it will get used often.
- Hand-selected bristle hair, longer than a Spalter
- Brush 'springs' into action (learn more)
- Softens unwanted brush/roller marks
- 4 uses: softening, strie, stipple, & moire
- A versatile brush for the price
- Water: Wash with soap, Oil: Thinned & wash w/ soap
SIZE TRANSLATIONS
| SIZE | BRUSH LENGTH | FERRULE WIDTH | FERRULE LENGTH |
HAIR LENGTH |
| 100 | 8.9" / 22.7cm | .16" / 4mm | 4" / 100mm | 2.2" / 55mm |
BRUSH SPECIFICATIONS
|
HAIR TYPE |
Natural Bristle |
|
BRUSH HOLD |
Drummer's Hold, Conductor's Hold |
|
USAGE |
Corner stippling; strie |
|
MEDIUM |
Water or Oil |
|
FERRULE |
Copper |
|
HANDLE |
Wooden flat short |
How-To Brush Care Guide
Prepare your brushes for their first use - read below.
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
- Wash the brush thoroughly with a mild dish soap in warm water and massage the hair to comb out the loose bristles. Rinse until there is no soap residue left in the brush.
- Ring the brush out by rolling it between your hands as if you were trying to make a fire with a stick to fluff out the brush.
- Let dry by hanging the brushes or lay it down at the edge of a table (a hog bristle will have a strong odor due to the bone glue used to attach the bristles. This will go away after a few washings.)
Repeat this process a few more times.
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
Proper cleaning procedure
for oil/water and large or small brushes:
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
Spalter Brush - Short (Bluetop) | GLZ-29
GLZ-29_Size-040
Regular price $10.00 Sale price $8.00 Save $2.00/
Shipping calculated at checkout.
Unique blue, silky fiber in our traditional spalter (mottler) shape and SHORTER length (38mm = 1.5"). This brush is primarily used to aid application of varnishes, thinned latex paints, and acrylic glazes. Unlike the "chip" brush that can be found in standard hardware stores, our spalter brush has a thick row of densely packed hair for ultimate performance and control.
- Uses: strie, moiré in woodgraining, and general tipping and smoothing to soften brushmarks
- Tips are manufactured to flower to hold more paint which will allow the brush to cut sharp edges.
- Best used in water based medium
- Tin ferrule with wooden flat handle
- Smaller sizes are great for window and door casing. Larger sizes for entire walls.
- Brush hold: Drummer's hold; quack motion
-
Soft, silky hair allows for delicate tipping for minimum brush marks.
-
SIZE TRANSLATIONS
SIZE BRUSH LENGTH FERRULE WIDTH FERRULE LENGTH HAIR LENGTH
40 7.6" / 19.2cm
.4" / 9mm 1.6" / 40mm 1.5" / 38mm 60 7.6" / 19.2cm .4" / 9mm 2.3" / 60mm 1.5" / 38mm
80 8.1" / 20.6cm .4" / 9mm 3.1" / 80mm 1.5" / 38mm
100 9.4" / 24cm .4" / 9mm 4" / 100mm 1.5" / 38mm
150 8.5" / 21.5cm .4" / 9mm 6" / 150mm 1.5" / 38mm
200 9.4" / 24cm .4" / 9mm 8" / 200mm 1.5" / 38mm
BRUSH SPECIFICATIONS
HAIR TYPE
Bluetop synthetic
USAGE
Strie; moire; softening paint; varnish
How-To Brush Care Guide
Prepare your brushes for their first use - read below.
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
- Wash the brush thoroughly with a mild dish soap in warm water and massage the hair to comb out the loose bristles. Rinse until there is no soap residue left in the brush.
- Ring the brush out by rolling it between your hands as if you were trying to make a fire with a stick to fluff out the brush.
- Let dry by hanging the brushes or lay it down at the edge of a table (a hog bristle will have a strong odor due to the bone glue used to attach the bristles. This will go away after a few washings.)
Repeat this process a few more times.
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
Proper cleaning procedure
for oil/water and large or small brushes:
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
Mini Flat Spalter Brush (Bordeaux Nylon) | MB-12
MB-12_Size-20
Regular price $19.80 Sale price $15.84 Save $3.96/
Shipping calculated at checkout.
Use this silky, soft synthetic thin spalter for wet-on-wet applications. Use for bathing marble fragments and toning wood heartgrain. Available in 2 sizes.
- Super soft, bordeaux synthetic hair
- Brush 'springs' into action (learn more)
- Perfect for onyx, malachite and Rouge Royal marble 'twisters'
- See also Cat Tongue
- Description: Bordeaux fiber, thin and soft
- Brush Care: water: Wash with soap
SIZE TRANSLATIONS
|
SIZE |
BRUSH LENGTH |
FERRULE WIDTH |
FERRULE LENGTH |
HAIR LENGTH |
|
20 |
6.5" / 16.4cm |
0.1"/5mm | 0.7"/20mm | 1.1"/30mm |
| 30 | 6.5" / 16.5cm | 0.1"/5mm | 1.1"/30mm | 1.3"/35mm |
BRUSH SPECIFICATIONS
|
HAIR TYPE
|
Bordeaux
|
|
BRUSH HOLD
|
Drummer's Hold
|
|
USAGE
|
Bathing marble fragments; wood heartgrain sketches
|
|
MEDIUM
|
Water
|
|
FERRULE
|
Tin
|
|
HANDLE
|
Wooden flat short
|
How-To Brush Care Guide
Prepare your brushes for their first use - read below.
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
- Wash the brush thoroughly with a mild dish soap in warm water and massage the hair to comb out the loose bristles. Rinse until there is no soap residue left in the brush.
- Ring the brush out by rolling it between your hands as if you were trying to make a fire with a stick to fluff out the brush.
- Let dry by hanging the brushes or lay it down at the edge of a table (a hog bristle will have a strong odor due to the bone glue used to attach the bristles. This will go away after a few washings.)
Repeat this process a few more times.
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
Proper cleaning procedure
for oil/water and large or small brushes:
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
Tooth Spalter Brush - Regular (Bluetop) | GLZ-26
GLZ-26_Size-040
Regular price $10.50 Sale price $8.40 Save $2.10/
Shipping calculated at checkout.
A blue, silky fiber tooth spalter has "teeth" cut out of a traditional spalter. These spaces allow for the brush to be used for different applications. This model mimics our traditional spalter shape and standard length (45mm = 1.75"). This brush is typically used to manipulate painting mediums such as glaze and paint by displacing medium. It can also be dipped into medium to create a print. The tooth spalter creates clear, strie lines with a series of parallel lines.
BRUSH SPECIFICATIONS
- Uses: Strie, general glazing, dry-brushing, straight graining (side grains) in woodgraining, use with thick paint or textures.
- Teeth are machine cut but meant to be randomly spaced. Generally, the teeth gaps are 3-4mm (.15") wide.
- Smaller sizes are great for window and door casing. Larger sizes for entire walls.
- Our blue brushes are styled with a white tip. These ends are manufactured to flower to hold more paint which will allow the brush to cut sharp edges.
- Brush hold: Drummer hold
- Best used in water mediums
- Tin ferrule with a short, flat handle
- General Brush Specifications: Thickness of brush = 9mm (.4"), Average Length of hair = 45mm (1.75")
SIZE TRANSLATIONS
| SIZE | BRUSH LENGTH | FERRULE WIDTH | FERRULE LENGTH |
HAIR LENGTH |
| 40 |
7.8" / 19.7cm |
.4" / 9mm | 1.6" / 40mm | 1.8" / 45mm |
| 60 | 7.8" / 19.7cm | .4" / 9mm | 2.3" / 60mm |
1.8" / 45mm |
| 80 |
7.8" / 19.7cm |
.4" / 9mm | 3.1" / 80mm |
1.8" / 45mm |
| 100 | 8.9" / 22.5cm | .4" / 9mm | 4" / 100mm |
1.8" / 45mm |
| 150 | 9.1" / 23.1cm | .4" / 9mm | 6" / 150mm |
1.8" / 45mm |
| 200 | 9.6" / 24.5cm | .4" / 9mm | 8" / 200mm | 1.8" / 45mm |
BRUSH SPECIFICATIONS
|
HAIR TYPE |
Bluetop synthetic fiber |
|
USAGE |
Strie, dry-brushing, straight graining in woodgraining, use with thick paint or textures. |
How-To Brush Care Guide
Prepare your brushes for their first use - read below.
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
- Wash the brush thoroughly with a mild dish soap in warm water and massage the hair to comb out the loose bristles. Rinse until there is no soap residue left in the brush.
- Ring the brush out by rolling it between your hands as if you were trying to make a fire with a stick to fluff out the brush.
- Let dry by hanging the brushes or lay it down at the edge of a table (a hog bristle will have a strong odor due to the bone glue used to attach the bristles. This will go away after a few washings.)
Repeat this process a few more times.
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
Proper cleaning procedure
for oil/water and large or small brushes:
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
Original Stubby Spalter Brush (Nylon, Bristle) | GLZ-07D
GLZ-07D_Size-040
Regular price $10.15 Sale price $7.11 Save $3.04/
Shipping calculated at checkout.
The spalter is one of the most used tools in our decorative brush kit. Unlike the average chip brush, our spalter has a thick row (1/3 inch) of short hair that is densely packed with a bristle/nylon blend for ultimate performance and control for today's water mediums. The smaller sizes have a variety of uses, from basecoats to final glazing, 'stretching' to softening. Available in 6 sizes.
- Nylon synthetic fiber with 50% natural bristle
- stretch glaze for ultimate consistency
- Softens unwanted brush/roller marks
- Excellent for applying thin varnish and waxes
- Fine/subtle strie
- Application/Usage: stretch; soften roller marks on basecoat & varnish applications; moire
- Preferred Medium: Oil/Water
- Brush Ferrule/Handle: copper, wooden flat short
- Brush Hair Type: Natural Bristle/Nylon blend
- Brush Hold: Drummer's Hold, "Quack Motion"
- Brush Care: Water: Wash with soap, Oil: Thinned & wash w/ soap
- Hair Length: 1.5-1.7" (38-45mm), 2" (51mm)
- Dia./width: 1.6" (40mm), 2.2" (60mm), 3.1" (80mm), 4", 6" (150mm), 8" (200mm)
How-To Brush Care Guide
Prepare your brushes for their first use - read below.
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
- Wash the brush thoroughly with a mild dish soap in warm water and massage the hair to comb out the loose bristles. Rinse until there is no soap residue left in the brush.
- Ring the brush out by rolling it between your hands as if you were trying to make a fire with a stick to fluff out the brush.
- Let dry by hanging the brushes or lay it down at the edge of a table (a hog bristle will have a strong odor due to the bone glue used to attach the bristles. This will go away after a few washings.)
Repeat this process a few more times.
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
Proper cleaning procedure
for oil/water and large or small brushes:
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
Original Stubby Tooth Spalter (Nylon, Bristle) | GLZ-08D
GLZ-08D_Size-100
Regular price $27.80 Sale price $19.46 Save $8.34/
Shipping calculated at checkout.
Our tooth spalter has been cut to create 'teeth'. In decorative painting, this bristle/blend brush is essential for a deep strie, brushed texture, & straight graining techniques in water mediums. Our spalters are over 1/3 " thick. This is a must for your decorative painting kit. Available in 6 sizes.
- Nylon synthetic fiber with 50% natural bristle
- Machine cut teeth
- The best brush for patina and aging techniques (dry-brushing)
- Pulling wet basecoat when a heavily brushed texture is desired
- Criss-cross techniques
- Application/Usage: strie; straight graining in wood
- Preferred Medium: Oil/Water
- Brush Ferrule/Handle: copper, wooden flat short
- Brush Hair Type: Natural Bristle/Nylon blend
- Brush Hold: Drummer's Hold
- Brush Care: Water: Wash with soap, Oil: Thinned & wash w/ soap
- Hair Length: 1.5-1.7" (38-45mm), 2" (51mm)
- Dia./width: 1.6" (40mm), 2.2" (60mm), 3.1" (80mm), 4", 6" (150mm), 8" (200mm)
How-To Brush Care Guide
Prepare your brushes for their first use - read below.
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
- Wash the brush thoroughly with a mild dish soap in warm water and massage the hair to comb out the loose bristles. Rinse until there is no soap residue left in the brush.
- Ring the brush out by rolling it between your hands as if you were trying to make a fire with a stick to fluff out the brush.
- Let dry by hanging the brushes or lay it down at the edge of a table (a hog bristle will have a strong odor due to the bone glue used to attach the bristles. This will go away after a few washings.)
Repeat this process a few more times.
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
Proper cleaning procedure
for oil/water and large or small brushes:
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
Spalter Brush - Long (Bluetop) | GLZ-37
GLZ-37_Size-40
Regular price $10.75 Sale price $8.60 Save $2.15/
Shipping calculated at checkout.
Unique blue, silky fiber in our traditional spalter (mottler) shape and LONGER length (average of 65mm long). This brush is primarily used to aid application of varnishes, thinned latex paints, and acrylic glazes. Unlike the "chip" brush that can be found in standard hardware stores, our spalter brush has a thick row of densely packed hair for ultimate performance and control.
- Uses: strie, moiré in woodgraining, and general tipping and smoothing to soften brushmarks
- Tips are manufactured to flower to hold more paint which will allow the brush to cut sharp edges.
- Best used in water based medium
- Tin ferrule with wooden flat handle
- Smaller sizes are great for window and door casing. Larger sizes for entire walls.
- Brush hold: Drummer's hold; quack motion
-
Soft, silky hair allows for delicate tipping for minimum brush marks.
-
SIZE TRANSLATIONS
SIZE BRUSH LENGTH FERRULE WIDTH FERRULE LENGTH HAIR LENGTH
40 8" / 20.4cm
.4" / 9mm 1.6" / 40mm 2.6" / 65mm 60 8.5" / 21.6cm .4" / 9mm 2.3" / 60mm 2.6" / 65mm 80 8.5" / 21.6cm .4" / 9mm 3.1" / 80mm 2.6" / 65mm 100 9.1" / 23cm .4" / 9mm 4" / 100mm 2.6" / 65mm 150 9.3" / 23.5cm .4" / 9mm 6" / 150mm 2.6" / 65mm 200 10.2" / 25.8cm .4" / 9mm 8" / 200mm 2.6" / 65mm
BRUSH SPECIFICATIONS
HAIR TYPE
Bluetop synthetic
USAGE
Strie; moire; softening paint; varnish
How-To Brush Care Guide
Prepare your brushes for their first use - read below.
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
- Wash the brush thoroughly with a mild dish soap in warm water and massage the hair to comb out the loose bristles. Rinse until there is no soap residue left in the brush.
- Ring the brush out by rolling it between your hands as if you were trying to make a fire with a stick to fluff out the brush.
- Let dry by hanging the brushes or lay it down at the edge of a table (a hog bristle will have a strong odor due to the bone glue used to attach the bristles. This will go away after a few washings.)
Repeat this process a few more times.
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
Proper cleaning procedure
for oil/water and large or small brushes:
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
Tooth Spalter Brush - Long (Bluetop) | GLZ-38
GLZ-38_Size-40
Regular price $11.25 Sale price $9.00 Save $2.25/
Shipping calculated at checkout.
Unique blue, silky fiber in our traditional spalter (mottler) shape and LONGER length (average 65mm ). This brush is primarily used to aid application of varnishes, thinned latex paints, and acrylic glazes. Unlike the "chip" brush that can be found in standard hardware stores, our spalter brush has a thick row of densely packed hair for ultimate performance and control.
- Uses: strie, moiré in woodgraining, and general tipping and smoothing to soften brush marks. This longer hair version creates stronger, more obvious strie.
- Tips are manufactured to flower to hold more paint which will allow the brush to cut sharp edges.
- Best used in water based medium
- Tin ferrule with wooden flat handle
- Smaller sizes are great for window and door casing. Larger sizes for entire walls
- Brush hold: Drummer's hold; quack motion
-
Soft, silky hair allows for delicate tipping for minimum brush marks
-
SIZE TRANSLATIONS
SIZE BRUSH LENGTH FERRULE WIDTH FERRULE LENGTH HAIR LENGTH
40 8" / 20.4cm
.4" / 9mm 1.6" / 40mm 2.6" / 65mm 60 8.5" / 21.6cm .4" / 9mm 2.3" / 60mm 2.6" / 65mm 80 8.5" / 21.6cm .4" / 9mm 3.1" / 80mm 2.6" / 65mm 100 9.1" / 23cm .4" / 9mm 4" / 100mm 2.6" / 65mm 150 9.3" / 23.5cm .4" / 9mm 6" / 150mm 2.6" / 65mm 200 10.2" / 25.8cm .4" / 9mm 8" / 200mm 2.6" / 65mm
BRUSH SPECIFICATIONS
HAIR TYPE
Bluetop synthetic
USAGE
Strie; moire; softening paint; varnish
How-To Brush Care Guide
Prepare your brushes for their first use - read below.
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
- Wash the brush thoroughly with a mild dish soap in warm water and massage the hair to comb out the loose bristles. Rinse until there is no soap residue left in the brush.
- Ring the brush out by rolling it between your hands as if you were trying to make a fire with a stick to fluff out the brush.
- Let dry by hanging the brushes or lay it down at the edge of a table (a hog bristle will have a strong odor due to the bone glue used to attach the bristles. This will go away after a few washings.)
Repeat this process a few more times.
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
Proper cleaning procedure
for oil/water and large or small brushes:
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
