14 products
14 products
Wire-Tied Veining Brush (Bristle) MB-02
MB-02_Size-02
Regular price $9.00/
Shipping calculated at checkout.
Use for creating veins in faux marble. Available in 4 sizes.
- Long, natural bristle
- Best used in oil mediums
- Wire tied bristle hair
- Description: Firm, bristle hair, domed tip
- Brush Care: Wash with soap
SIZE TRANSLATIONS
|
SIZE |
BRUSH LENGTH |
FERRULE WIDTH |
FERRULE LENGTH |
HAIR LENGTH |
|
2 |
.1" / 5mm |
.1" / 5mm |
1" / 27mm |
|
|
4 |
.1" / 5mm |
.1" / 5mm |
1" / 27mm |
|
|
6 |
. 1" / 5mm | .1" / 5mm |
1.2" / 33mm |
|
|
10 |
|
.2" / 5.1mm |
1.2" / 33mm |
BRUSH SPECIFICATIONS
|
HAIR TYPE |
Natural Bristle |
|
BRUSH HOLD |
Conductor's Hold |
|
USAGE |
Veining for faux marble in oil / water mediums |
|
MEDIUM |
Oil or Water |
|
FERRULE |
Wire-tied |
|
HANDLE |
Wooden round long |
How-To Brush Care Guide
Prepare your brushes for their first use - read below.
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
- Wash the brush thoroughly with a mild dish soap in warm water and massage the hair to comb out the loose bristles. Rinse until there is no soap residue left in the brush.
- Ring the brush out by rolling it between your hands as if you were trying to make a fire with a stick to fluff out the brush.
- Let dry by hanging the brushes or lay it down at the edge of a table (a hog bristle will have a strong odor due to the bone glue used to attach the bristles. This will go away after a few washings.)
Repeat this process a few more times.
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
Proper cleaning procedure
for oil/water and large or small brushes:
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
Chiqueteur | MB-09
MB-09_Size-08
Regular price $125.00/
Shipping calculated at checkout.
The Rolls Royce of faux marble brushes, the chiqueteur [sheik-ter] is used for painting backgrounds of faux marble and stone finishes. Experience ultimate controlled randomness with this specialty brush. Available in 2 sizes.
- Soft square tip squirrel hair with 5-10% synthetic nylon
- Wire tied natural quill
- No more messy hands
- Great for skewering real gold leaf w/o scratching
- Brush Care: Water: Wash with soap, Oil: Thinned & wash w/ soap
SIZE TRANSLATIONS
| SIZE | BRUSH LENGTH | FERRULE WIDTH | FERRULE LENGTH |
HAIR LENGTH
|
|
8
|
1.1"/30mm
|
1.1"/30mm
|
2.4"/61mm
|
|
|
10
|
1.1"/30mm
|
1.1"/30mm
|
2.6"/66mm
|
BRUSH SPECIFICATIONS
|
HAIR TYPE |
Squirrel |
|
BRUSH HOLD |
Pencil Hold |
|
USAGE |
Marble, Fragmenting, Chiqueteuring, Stone Texture |
|
MEDIUM |
Oil or Water |
|
FERRULE |
Wire-Tied Quilled |
|
HANDLE |
Wooden Round Medium |
How-To Brush Care Guide
Prepare your brushes for their first use - read below.
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
- Wash the brush thoroughly with a mild dish soap in warm water and massage the hair to comb out the loose bristles. Rinse until there is no soap residue left in the brush.
- Ring the brush out by rolling it between your hands as if you were trying to make a fire with a stick to fluff out the brush.
- Let dry by hanging the brushes or lay it down at the edge of a table (a hog bristle will have a strong odor due to the bone glue used to attach the bristles. This will go away after a few washings.)
Repeat this process a few more times.
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
Proper cleaning procedure
for oil/water and large or small brushes:
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
2-Header Pointed Brecher Brush (Sable) | MB-04
MB-04
Regular price $71.00/
Shipping calculated at checkout.
Use this pointed, 2-header for painting breche marble.
- Brush Care: Water: Wash with soap, Oil: Thinned & lard
SIZE TRANSLATIONS
| FERRULE WIDTH | FERRULE LENGTH | LENGTH OF QUILL | HAIR LENGTH ABOVE FERRULE | HAIR LENGTH ABOVE QUILL |
| .5" / 15mm | .7" / 20mm | .28" / 7mm | 1.4" / 36mm | 1.4" / 36mm |
BRUSH SPECIFICATIONS
|
HAIR TYPE |
Natural Sable Hair |
|
BRUSH HOLD |
Conductor's Hold, Pencil Hold |
|
USAGE |
Fine marble breching; figure design in wood heartgrain |
|
MEDIUM |
Oil, Water |
|
FERRULE |
Wire-tied quill |
|
HANDLE |
Wooden round long |
How-To Brush Care Guide
Prepare your brushes for their first use - read below.
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
- Wash the brush thoroughly with a mild dish soap in warm water and massage the hair to comb out the loose bristles. Rinse until there is no soap residue left in the brush.
- Ring the brush out by rolling it between your hands as if you were trying to make a fire with a stick to fluff out the brush.
- Let dry by hanging the brushes or lay it down at the edge of a table (a hog bristle will have a strong odor due to the bone glue used to attach the bristles. This will go away after a few washings.)
Repeat this process a few more times.
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
Proper cleaning procedure
for oil/water and large or small brushes:
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
Wire-Tied Veining Brush (Samina Nylon) | MB-03
MB-03_Size-06
Regular price $14.50/
Shipping calculated at checkout.
Use this veining brush for faux marble to keep a desirable round and domed shape, making this our primary water veining brush. Soft, synthetic fiber, domed tip. Available in 2 sizes. Brush Care: Wash with soap
SIZE TRANSLATIONS
| SIZE | BRUSH LENGTH | FERRULE WIDTH | FERRULE LENGTH |
HAIR LENGTH |
| 6 | .19" / 4.9mm | .19" / 4.9mm | 1.26 / 32mm | |
| 8 | .2" / 5.1mm | .2" / 5.1mm | 1.3" / 33mm |
BRUSH SPECIFICATIONS
|
HAIR TYPE |
Synthetic Samina Fiber |
|
BRUSH HOLD |
Conductor's Hold |
|
USAGE |
Veining for faux marble in water mediums |
|
MEDIUM |
Water |
|
FERRULE |
Wire-tied |
|
HANDLE |
Wooden round long |
How-To Brush Care Guide
Prepare your brushes for their first use - read below.
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
- Wash the brush thoroughly with a mild dish soap in warm water and massage the hair to comb out the loose bristles. Rinse until there is no soap residue left in the brush.
- Ring the brush out by rolling it between your hands as if you were trying to make a fire with a stick to fluff out the brush.
- Let dry by hanging the brushes or lay it down at the edge of a table (a hog bristle will have a strong odor due to the bone glue used to attach the bristles. This will go away after a few washings.)
Repeat this process a few more times.
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
Proper cleaning procedure
for oil/water and large or small brushes:
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
Wire-Tied Veining Brush (Bordeaux Nylon) | MB-01
MB-01_Size-04
Regular price $13.00/
Shipping calculated at checkout.
Use to create veins for faux marble. Available in 3 sizes.
- Slightly stiff, domed tip, synthetic, bordeaux fiber
- Brush 'springs' into action (learn more)
- Wire tied
- See also TL-1, TL-2
- Brush Care: Water: Wash with soap, Oil: Thinned & lard
SIZE TRANSLATIONS
|
SIZE |
BRUSH LENGTH |
FERRULE WIDTH |
FERRULE LENGTH |
HAIR LENGTH |
|
4 |
.1" / 5mm | .1" / 5mm |
1.1" / 30mm |
|
|
6 |
.2" / 6mm |
.2" / 6mm |
1.2" / 33mm |
|
|
8 |
. 2" / 6mm | . 2" / 6mm |
1.2" / 33mm |
BRUSH SPECIFICATIONS
|
HAIR TYPE |
Synthetic Bordeaux Fiber |
|
BRUSH HOLD |
Conductor's Hold |
|
USAGE |
Veining for faux marble in water mediums |
|
MEDIUM |
Water |
|
FERRULE |
Wire-tied |
|
HANDLE |
Wooden round long |
How-To Brush Care Guide
Prepare your brushes for their first use - read below.
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
- Wash the brush thoroughly with a mild dish soap in warm water and massage the hair to comb out the loose bristles. Rinse until there is no soap residue left in the brush.
- Ring the brush out by rolling it between your hands as if you were trying to make a fire with a stick to fluff out the brush.
- Let dry by hanging the brushes or lay it down at the edge of a table (a hog bristle will have a strong odor due to the bone glue used to attach the bristles. This will go away after a few washings.)
Repeat this process a few more times.
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
Proper cleaning procedure
for oil/water and large or small brushes:
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
3-Header Flat Chiqueteur Brush (Squirrel) | MB-07
MB-07
Regular price $95.00/
Shipping calculated at checkout.
Use this flat tip 3-header to create texture for faux marble projects. The square or flat tip is primarily for creating marble backgrounds and crystallization.
- Natural black soft squirrel with 5-10% synthetic nylon
- Reach the smallest, intricate surfaces like brackets, mantles, & fluting
- Brush Care: Oil: Thinned & lard, Water: Wash with soap
SIZE TRANSLATIONS
| FERRULE WIDTH | FERRULE LENGTH | LENGTH OF QUILL | HAIR LENGTH ABOVE FERRULE | HAIR LENGTH ABOVE QUILL |
| 1.1" / 30mm | .1.1" / 30mm | .4" / 11mm | 2.3" / 59mm |
BRUSH SPECIFICATIONS
|
HAIR TYPE |
Natural Squirrel Hair |
|
BRUSH HOLD |
Pencil hold |
|
USAGE |
Background texture; marble fragmenting; flaming; chiqueteuring |
|
MEDIUM |
Oil or Water |
|
FERRULE |
Wire-tied quill |
|
HANDLE |
Wooden round long |
How-To Brush Care Guide
Prepare your brushes for their first use - read below.
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
- Wash the brush thoroughly with a mild dish soap in warm water and massage the hair to comb out the loose bristles. Rinse until there is no soap residue left in the brush.
- Ring the brush out by rolling it between your hands as if you were trying to make a fire with a stick to fluff out the brush.
- Let dry by hanging the brushes or lay it down at the edge of a table (a hog bristle will have a strong odor due to the bone glue used to attach the bristles. This will go away after a few washings.)
Repeat this process a few more times.
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
Proper cleaning procedure
for oil/water and large or small brushes:
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
Chiqueteur Brush (Samina Nylon) | MB-15
MB-15
Regular price $110.00/
Shipping calculated at checkout.
This Chiqueteur [sheik-ter] is the most often used brush in painting backgrounds for faux marble and stone finishes.
- Super soft, samina synthetic fiber with flat tip
- Wire tied natural quill
- No more messy hands
- Makes an ultra fine print when working on small areas like molding and when painting Pietra Dura
- Brush Care: water: Wash with soap
SIZE TRANSLATIONS
|
SIZE |
BRUSH LENGTH |
FERRULE WIDTH |
FERRULE LENGTH |
HAIR LENGTH |
|
8 |
1.1" /27.5mm |
1.1" / 27.5mm |
1.9" / 49mm |
BRUSH SPECIFICATIONS
|
HAIR TYPE |
Samina Synthetic |
|
BRUSH HOLD |
Quack Motion |
|
USAGE |
Marble fragmenting; chiqueteuring; stone texture |
|
MEDIUM |
Water |
|
FERRULE |
Tin |
|
HANDLE |
Wooden round medium |
How-To Brush Care Guide
Prepare your brushes for their first use - read below.
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
- Wash the brush thoroughly with a mild dish soap in warm water and massage the hair to comb out the loose bristles. Rinse until there is no soap residue left in the brush.
- Ring the brush out by rolling it between your hands as if you were trying to make a fire with a stick to fluff out the brush.
- Let dry by hanging the brushes or lay it down at the edge of a table (a hog bristle will have a strong odor due to the bone glue used to attach the bristles. This will go away after a few washings.)
Repeat this process a few more times.
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
Proper cleaning procedure
for oil/water and large or small brushes:
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
2-Header Pointed Brecher Brush (Samina Nylon) | MB-05
MB-05_Size-0
Regular price $54.00/
Shipping calculated at checkout.
Use this pointed, 2-header for painting faux breche marble.
- Sable-like soft, synthetic samina fiber
- Wire tied natural quill
- Use with our SINGLE HEAD BRECHER
- Soft, synthetic fiber, 2-pointed tips, wire-tied quill
- Brush Care: Wash with soap
SIZE TRANSLATIONS
| SIZE | FERRULE WIDTH | FERRULE LENGTH | LENGTH OF QUILL | HAIR LENGTH ABOVE FERRULE | HAIR LENGTH ABOVE QUILL |
| 0 |
|
.79" / 20mm | .28" / 7mm | 1.7" / 42mm | 1.4" / 36mm |
| 1 | .83" / 21mm | .29" / 7.5mm | 2" / 52mm | 1.6" / 40mm |
BRUSH SPECIFICATIONS
|
HAIR TYPE |
Synthetic Samina Fiber |
|
BRUSH HOLD |
Conductor's Hold, Pencil Hold |
|
USAGE |
Marble breching; Hooking |
|
MEDIUM |
Water |
|
FERRULE |
Wire-tied quill |
|
HANDLE |
Wooden round long |
How-To Brush Care Guide
Prepare your brushes for their first use - read below.
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
- Wash the brush thoroughly with a mild dish soap in warm water and massage the hair to comb out the loose bristles. Rinse until there is no soap residue left in the brush.
- Ring the brush out by rolling it between your hands as if you were trying to make a fire with a stick to fluff out the brush.
- Let dry by hanging the brushes or lay it down at the edge of a table (a hog bristle will have a strong odor due to the bone glue used to attach the bristles. This will go away after a few washings.)
Repeat this process a few more times.
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
Proper cleaning procedure
for oil/water and large or small brushes:
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
Short Brecher Brush (Samina Nylon) | MB-18
MB-18
Regular price $18.00/
Shipping calculated at checkout.
TRIPLE ZERO small size. Use this brecher, [breh-sher] to create thin line fragments to thick veins with a flick of the wrist.
- Sable-like, soft samina synthetic fiber
- Wire tied natural quill
- Great for breching on molding
- Best for bathing breche fragments
- Brush 'springs' into action (learn more)
SIZE TRANSLATIONS
|
SIZE |
BRUSH LENGTH |
FERRULE WIDTH |
FERRULE LENGTH |
HAIR LENGTH |
|
|
0.1"/5mm | 0.1"/5mm | 1.1"/30mm |
BRUSH SPECIFICATIONS
|
HAIR TYPE |
|
|
BRUSH HOLD |
|
|
USAGE |
|
|
MEDIUM |
|
|
FERRULE |
|
|
HANDLE |
|
How-To Brush Care Guide
Prepare your brushes for their first use - read below.
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
- Wash the brush thoroughly with a mild dish soap in warm water and massage the hair to comb out the loose bristles. Rinse until there is no soap residue left in the brush.
- Ring the brush out by rolling it between your hands as if you were trying to make a fire with a stick to fluff out the brush.
- Let dry by hanging the brushes or lay it down at the edge of a table (a hog bristle will have a strong odor due to the bone glue used to attach the bristles. This will go away after a few washings.)
Repeat this process a few more times.
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
Proper cleaning procedure
for oil/water and large or small brushes:
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
Long Brecher Brush (Samina Nylon) | MB-14
MB-14_Size-00
Regular price $18.00/
Shipping calculated at checkout.
Use this brecher, [breh-sher] to create thin line fragments to thick veins with a flick of the wrist. Available in 3 sizes.
SIZE TRANSLATIONS
|
SIZE |
BRUSH LENGTH |
FERRULE WIDTH |
FERRULE LENGTH |
HAIR LENGTH |
|
00 |
0.2"/7mm | 0.2"/6mm |
1.6"/43mm |
|
|
2 |
0.3"/10mm | 0.3"/10mm | 2"/51mm | |
|
3 |
0.4"/11mm | 0.4"/11mm | 2.1"/55mm |
BRUSH SPECIFICATIONS
|
HAIR TYPE |
Samina |
|
BRUSH HOLD |
Conductor's Hold, Drummer's Hold |
|
USAGE |
Breche marble; bathing |
|
MEDIUM |
Water |
|
FERRULE |
Quill |
|
HANDLE |
Wooden round long |
How-To Brush Care Guide
Prepare your brushes for their first use - read below.
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
- Wash the brush thoroughly with a mild dish soap in warm water and massage the hair to comb out the loose bristles. Rinse until there is no soap residue left in the brush.
- Ring the brush out by rolling it between your hands as if you were trying to make a fire with a stick to fluff out the brush.
- Let dry by hanging the brushes or lay it down at the edge of a table (a hog bristle will have a strong odor due to the bone glue used to attach the bristles. This will go away after a few washings.)
Repeat this process a few more times.
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
Proper cleaning procedure
for oil/water and large or small brushes:
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
2-Header Pointed Brecher Brush (Squirrel) | MB-06
MB-06
Regular price $55.00/
Shipping calculated at checkout.
Use this pointed 2-header for painting breche faux marble.
- Brush Care: Water: Wash with soap, Oil: Thinned & lard
SIZE TRANSLATIONS
| FERRULE WIDTH | FERRULE LENGTH | LENGTH OF QUILL | HAIR LENGTH ABOVE FERRULE | HAIR LENGTH ABOVE QUILL |
| .5" / 15mm | .8" / 21mm | .28" / 7mm | 2" / 51mm | 1.6" / 40mm |
BRUSH SPECIFICATIONS
|
HAIR TYPE |
Natural Squirrel Hair |
|
BRUSH HOLD |
Conductor's Hold, Pencil Hold |
|
USAGE |
Marble breching; hooking |
|
MEDIUM |
Oil, Water |
|
FERRULE |
Wire-tied quill |
|
HANDLE |
Wooden round long |
How-To Brush Care Guide
Prepare your brushes for their first use - read below.
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
- Wash the brush thoroughly with a mild dish soap in warm water and massage the hair to comb out the loose bristles. Rinse until there is no soap residue left in the brush.
- Ring the brush out by rolling it between your hands as if you were trying to make a fire with a stick to fluff out the brush.
- Let dry by hanging the brushes or lay it down at the edge of a table (a hog bristle will have a strong odor due to the bone glue used to attach the bristles. This will go away after a few washings.)
Repeat this process a few more times.
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
Proper cleaning procedure
for oil/water and large or small brushes:
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
3-Header Pointed Chiqueteur Brush (Samina Nylon) | MB-08
MB-08
Regular price $89.00/
Shipping calculated at checkout.
Use this pointed 3-header for painting breche veins in faux marble.
- samina synthetic fiber
- Wire tied natural quill
- Create a fine, multidirectional, veined background.
- Background texture for Sea Green, Yellow Flower, Imperador and more
- Brush Care: Wash with soap
SIZE TRANSLATIONS
| FERRULE WIDTH | FERRULE LENGTH | LENGTH OF QUILL | HAIR LENGTH ABOVE FERRULE | HAIR LENGTH ABOVE QUILL |
| 1" / 27mm | 1" / 27mm | .35" / 9mm | 2" / 51mm | 1.6" / 40mm |
BRUSH SPECIFICATIONS
|
HAIR TYPE |
Synthetic Samina Fiber |
|
BRUSH HOLD |
Pencil Hold |
|
USAGE |
Marble breching; hooking |
|
MEDIUM |
Water |
|
FERRULE |
Wire-tied quill |
|
HANDLE |
Wooden round long |
How-To Brush Care Guide
Prepare your brushes for their first use - read below.
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
- Wash the brush thoroughly with a mild dish soap in warm water and massage the hair to comb out the loose bristles. Rinse until there is no soap residue left in the brush.
- Ring the brush out by rolling it between your hands as if you were trying to make a fire with a stick to fluff out the brush.
- Let dry by hanging the brushes or lay it down at the edge of a table (a hog bristle will have a strong odor due to the bone glue used to attach the bristles. This will go away after a few washings.)
Repeat this process a few more times.
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
Proper cleaning procedure
for oil/water and large or small brushes:
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
3-Header Pointed Brecher Brush (Samina Nylon) | MB-17
MB-17
Regular price $92.00/
Shipping calculated at checkout.
Use this 3-headed brecher for faux marble veins and creating a fine, multidirectional marble background .
- Samina fiber, 3-pointed tips
- Brush Care: water: Wash with soap
- samina synthetic fiber
- Wire tied natural quill
- Background texture for Sea Green, Yellow Flower, Imperador and more
- Great for over glazing faux marble and fissures
SIZE TRANSLATION
|
SIZE |
BRUSH LENGTH |
FERRULE WIDTH |
FERRULE LENGTH |
HAIR LENGTH |
|
0.5"/15mm |
1"/27mm |
1.9"/48mm |
BRUSH SPECIFICATIONS
|
HAIR TYPE
|
Samina
|
|
BRUSH HOLD
|
Conductor's Hold, Pencil Hold
|
|
USAGE
|
Marble breching; hooking
|
|
MEDIUM
|
Water
|
|
FERRULE
|
Quill
|
|
HANDLE
|
Wooden round medium
|
How-To Brush Care Guide
Prepare your brushes for their first use - read below.
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
- Wash the brush thoroughly with a mild dish soap in warm water and massage the hair to comb out the loose bristles. Rinse until there is no soap residue left in the brush.
- Ring the brush out by rolling it between your hands as if you were trying to make a fire with a stick to fluff out the brush.
- Let dry by hanging the brushes or lay it down at the edge of a table (a hog bristle will have a strong odor due to the bone glue used to attach the bristles. This will go away after a few washings.)
Repeat this process a few more times.
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
Proper cleaning procedure
for oil/water and large or small brushes:
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
