More
286 products
286 products
286 products
GOLDEN PRO Slow Dry Fluid Acrylic
ITEM #: PGZ-09_B-8oz
PRICE: $19.49 Regular priceUse right out of the bottle or tint a glazing medium for the longest open time. GOLDEN Pro Finishes Slow Dry Fluid Acrylics are acrylic waterborne paints designed to provide decorative painters with a true color palette. Painters will enjoy a strong bond to the substrate and a long open time. Dries to a satin sheen. Use these colors to tint a glaze or use right out of the bottle. Available in 23 colors.
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
Spalter Brush (Bristle, Nylon) | GLZ-07
ITEM #: GLZ-07_Size040
PRICE: $10.95 Regular priceThe spalter is one of the most used tools in our decorative brush kit. Unlike the average cheap brush, our spalter has a thick row (1/3 inch) of short hair that is densely packed with a bristle/nylon blend for ultimate performance and control for today's water mediums. The smaller sizes have a variety of uses, from basecoats to final glazing, 'stretching' to softening. Available in 8 sizes. Amazing for entire wall strie or criss-cross.
| SIZE | BRUSH LENGTH | FERRULE WIDTH | FERRULE LENGTH |
HAIR LENGTH |
| 40 |
6.9" / 17.6cm |
.4" / 9mm | 1.6" / 40mm | 1.4" / 36mm |
| 60 |
7.5" / 19cm |
.4" / 9mm | 2.4" / 60mm | 1.4" / 36mm |
| 80 | 7.6" / 19.3cm | .4" / 9mm | 3.1" / 80mm | 1.4" / 36mm |
| 100 | 8.3" / 21cm | .4" / 9mm | 4" / 100mm | 1.6" / 41mm |
| 150 | 8.8" / 22.4cm | .4" / 9mm | 6" / 150mm | 1.8" / 46mm |
| 200 | 9.7" / 24.7cm | .4" / 9mm | 8" / 200mm | 1.9" / 47mm |
| 250 | 9.5" / 24.2cm | .4" / 9mm | 9.9" / 250mm | 1.8" / 46mm |
| 300 | 9.6" / 24.3cm | .4" / 9mm | 11.8" / 300mm | 1.7" / 44mm |
|
HAIR TYPE |
Natural Bristle / Nylon blend |
|
BRUSH HOLD |
Drummer's Hold, "Quack Motion" |
|
USAGE |
Soften roller marks on base coat & varnish applications; Moire |
|
MEDIUM |
Water or Oil |
|
FERRULE |
Copper |
|
HANDLE |
Wooden flat short |
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
Spalter Brush - Regular (Bluetop) | GLZ-24
ITEM #: GLZ-24_Size-040
PRICE: $11.25 Regular priceUnique blue, silky fiber in our traditional spalter (mottler) shape and standard length (45mm = 1.75"). This brush is primarily used to aid application of varnishes, thinned latex paints, and acrylic glazes. Unlike the "chip" brush that can be found in standard hardware stores, our spalter brush has a thick row of densely packed hair for ultimate performance and control.
| SIZE | BRUSH LENGTH | FERRULE WIDTH | FERRULE LENGTH |
HAIR LENGTH |
| 40 |
7.8" / 19.7cm |
.4" / 9mm | 1.6" / 40mm | 1.8" / 45mm |
| 60 | 7.8" / 19.7cm | .4" / 9mm | 2.3" / 60mm |
1.8" / 45mm |
| 80 |
7.8" / 19.7cm |
.4" / 9mm | 3.1" / 80mm |
1.8" / 45mm |
| 100 | 8.9" / 22.5cm | .4" / 9mm | 4" / 100mm |
1.8" / 45mm |
| 150 | 9.1" / 23.1cm | .4" / 9mm | 6" / 150mm |
1.8" / 45mm |
| 200 | 9.6" / 24.5cm | .4" / 9mm | 8" / 200mm |
1.8" / 45mm |
|
HAIR TYPE |
Bluetop synthetic |
|
USAGE |
Strie; moire; softening paint; varnish |
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
Tooth Spalter Brush (Bristle, Nylon) | GLZ-08
ITEM #: GLZ-08_Size-040
PRICE: $12.70 Regular priceOur tooth spalter has "teeth" cut out of a traditional spalter. These spaces allow for the brush to be used for different applications. This model mimics our traditional spalter shape and standard length. This brush is typically used to manipulate painting mediums such as glaze and paint by displacing medium. It can also be dipped into medium to create a print. The tooth spalter creates clear, strie lines with a series of parallel lines.
| SIZE | BRUSH LENGTH | FERRULE WIDTH | FERRULE LENGTH |
HAIR LENGTH |
| 40 | 6.9" / 17.6cm | .4" / 9mm | 1.6" / 40mm | 1.5" / 37mm |
| 60 | 7.2" / 18.4cm | .4" / 9mm | 2.4" / 60mm | 1.6" / 40mm |
| 80 |
7.6" / 19.4cm |
.4" / 9mm | 3.1" / 80mm | 1.4" / 36mm |
| 100 |
8.2" / 20.9cm |
.4" / 10mm | 4" / 100mm | 1.7" / 42mm |
| 150 |
8.8" / 22.3cm |
.4" / 10mm | 6" / 150mm | 1.9" / 47mm |
| 200 | 9.8" / 24.8cm | .4" / 10mm | 8" / 200mm | 2.1" / 54mm |
|
HAIR TYPE |
Natural Bristle / Nylon blend |
|
BRUSH HOLD |
Drummer's Hold |
|
USAGE |
Strie; straight graining in wood |
|
MEDIUM |
Water or Oil |
|
FERRULE |
Copper |
|
HANDLE |
Wooden flat short |
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
PRO Pointed Glazing Brush (Bluetop) | GLZ-45
ITEM #: GLZ-45_Size-00000
PRICE: $13.25 Regular priceOur BLUETOP PRO SERIES POINTED glazing (sash) brushes have a classic round shape for ultimate paint medium dispersion. It is used to apply glaze, paint, wax, and thin textures. Use like a standard paint brush or scrubbing motion.
| SIZE | BRUSH LENGTH | FERRULE WIDTH | HAIR LENGTH |
| 00000 |
10.6" / 26.8cm |
.45" / 11mm |
1.9" / 48mm |
| 000 | 11.6" / 29.5cm | .6" / 15mm | 2.1" / 53mm |
| 0 | 11.4" / 29cm | .7" / 18mm | 2.3" / 58mm |
| 2 | 12.2" / 31cm | .83" / 21mm | 2.6" / 66mm |
| 4 | 12.6" / 32.1cm | .98" / 25mm | 2.9" / 73mm |
| 6 | 13.2" / 33.5cm | 1.2" / 29mm | 3" / 77mm |
| 8 |
13.4" / 34.1cm |
1.4" / 34mm | 3.2" / 81mm |
|
HAIR TYPE |
Bluetop synthetic fiber |
|
USAGE |
Application of varnish, paint, glaze medium |
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
Graining Flogger (Black Bristle) | WD-04
ITEM #: WD-04_Size-60
PRICE: $39.15 Regular price| SIZE | BRUSH LENGTH | FERRULE WIDTH | FERRULE LENGTH |
HAIR LENGTH |
| 60 | 13.4" / 34cm | 0.2" / 7mm | 2.4" / 60mm |
4.9" / 125mm |
| 80 | 13.6" / 34.5cm | 0.2" / 7mm | 3.1" / 80mm | 4.9" / 125mm |
| 100 | 14.2" / 36cm | 0.2" / 7mm | 3.9" / 100mm | 4.9" / 125mm |
| 120 | 12" / 30.5cm | 0.2" / 7mm | 4.7" / 120mm | 4.9" / 125mm |
BRUSH SPECIFICATIONS
|
HAIR TYPE |
Black Bristle |
|
BRUSH HOLD |
Drummer's Hold |
|
USAGE |
Background Woodgraining; pores |
|
MEDIUM |
Water/Oil |
|
FERRULE |
Copper |
|
HANDLE |
Wooden, Flat, Long |
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
GOLDEN Matte Fluid Acrylics | PFA111D
ITEM #: PFA-111_AC-4oz
PRICE: $12.86 Regular price Regularly: $26.79 Sale price Save $13.93GOLDEN FLUID ACRYLICS are self-leveling paints that dry to a matte (or satin) finish. Pierre Finkelstein has hand-picked this full palette of colors for a variety of decorative painting projects., These colors are invaluable for tinting small amounts of paint, trompe l'oeil tonalities, and for countless touch-up projects. Most of the colors listed here are MATTE, but some are SATIN (for the lack of availability in MATTE).
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
Badger Softener | GLZ-15
ITEM #: GLZ-15_Size-02
PRICE: $86.65 Regular priceOur classic hand mounted badger brush is made out of the finest grouping of water badger hair. Stay clear of the 'BAD'-ger impostor whose hair is made out of goat hair that has been dipped into black paint to look like a real badger. Stiffer hair is good for softening and easier to clean as you go.
| SIZE | BRUSH LENGTH | FERRULE WIDTH | FERRULE LENGTH |
HAIR LENGTH |
| 2 | 8.38"/ 21.3cm | .8" / 20mm | 2.2" / 55mm | 2.6" / 65mm |
| 4 | 10.6" / 26.8cm | .8" / 20mm | 4.1" / 104mm | 2.7"/ 69mm |
| 6 | .8" / 20mm | 6.3" / 160mm | 2.7" / 69mm |
|
HAIR TYPE |
Badger |
|
BRUSH HOLD |
Conductor's Hold |
|
USAGE |
Softening |
|
MEDIUM |
Water |
|
FERRULE |
Wood |
|
HANDLE |
Wooden round medium |
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
GOLDEN PRO Glazing Medium
ITEM #: PGZ-11_1
PRICE: $22.29 Regular price Sale priceVersatile glazing medium with the longest open time.
GOLDEN PRO 32 oz. Glazing Medium, provides the extended dry-time of traditional oil mediums without compromising strength or transparency. Dries to a satin finish. Tint with water-compatible colors like DISPERSIONS, or, for the longest open time, use with Slow-dry FLUID COLORS . Use for large-scale projects. Working time is typically 15-45 minutes depending on technique and substrate. For a sheen that is more matte, mix with MATTING ADDITIVE.
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
Mixol® Universal Color Tints
ITEM #: PMX-01_B01_20ml
PRICE: $5.76 Regular price Regularly: $6.06 Sale price Save $0.30Mixol offers the highest quality Universal Tints on the market. Produced in Germany for more than 35 years, Mixol is compatible with almost any paint and coating. The full assortment of 33 colors mixes easily with shellacs, lacquers, primers and fillers.
Mixol is known for its high concentration of pigment, sophisticated color palette, and ease of mixing. They are highly resistant to frost and heat damage. They have an indefinite shelf life, and because they are binder-free, they will not dry out or thicken.
Fifteen Mixol Oxide colors were created to meet the growing demand for adding color to fast-drying varnishes and paints. Oxide colorants can even be used with cement and mortar and are colorfast and weatherproof.
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
GOLDEN PRO Sheer Glazing Medium
ITEM #: PGZ-12_1
PRICE: $22.29 Regular price Sale priceThinner glazing medium for a sheer finish.
GOLDEN PRO Sheer glazing medium provides the extended dry-time of traditional oil mediums without compromising strength or transparency. Dries to a satin finish. Tint with water-compatible colors like DISPERSIONS, or, for the longest open time, use with Slow-dry FLUID COLORS . Use this ultra-thin glazing medium in specialized glazing techniques such as faux marble and woodgraining. Use the Glazing medium glaze for large-scale projects. Working time is typically 15-45 minutes depending on technique and substrate. For a sheen that is more matte, mix with MATTING ADDITIVE.
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
LIVE Woodgraining Fundamentals Series with Pierre Finkelstein
ITEM #: PFI-02_ALL
PRICE: $120.00 Regular priceJoin Pierre Finkelstein for his 3-part weekly series each featuring 1 ½ hours of online demonstration of Woodgraining veining fundamentals. This sketch-based instruction will be useful for all levels of painters. Pierre will breakdown graining into its simplest form by focusing on the basic structure of the heartgrain as well as straightgraining.
He will demonstrate how to correctly hold different brushes to create a variety of wood patterns, composition and flow, and wood layout. You will learn how to design and compose most of the heart wood graining in a realistic manner on this drawing based instruction. Pierre will simplify teaching the structure of the grain by minimizing color with these medium to small scale drawings to understand graining pattern fundamentals.
Pierre will also review some technical skills to do burls, moire based woods (such as birds eye, satin wood, etc). He will also review different species of wood and wood formation based on milling cuts.
* Materials needed: paper, pencil, water board & brush and optional kit to practice along BKIT-14
GET THE OPTIONAL BRUSH KIT TO PRACTICE ALONG
Part 1 - Tuesday Feb 1st 4-5:30pm EST(new date)
Part 2 - Tuesday Feb 8th 4-5:30pm EST (new date)
Part 3 - Tuesday Feb 15th 4-5:30pm EST(new date)
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
Graining Tooth Veinette (Bristle) | WD-03
ITEM #: WD-03_Size-35
PRICE: $38.70 Regular priceDon't miss out on this unique woodgraining brush. Use this high quality bristle hair brush to help create the delicate grains in woodgraining. Long bristle hair, notched teeth, for side graining. Brush Care: Water: Wash with soap, Oil: Thinned & wash w/ soap
| SIZE | BRUSH LENGTH | FERRULE WIDTH | FERRULE LENGTH |
HAIR LENGTH |
| 35 | .1" / 2.5mm | 1.4" /35mm | 2.6" /65mm | |
| 45 | 10.6" / 26.9cm | .12" /3mm | 1.8" /46mm | 2.8" /71mm |
| 60 | .22" /5.5mm | 2.5" /63mm | 3.2" /81mm |
|
HAIR TYPE |
Natural Bristle |
|
BRUSH HOLD |
Drummer's Hold, Conductor's Hold |
|
USAGE |
Straight graining/veining; onyx veins; wood heartgrain |
|
MEDIUM |
Water or Oil |
|
FERRULE |
Tin |
|
HANDLE |
Wooden flat medium |
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
Deerhoof Liner Striper Brush (Skunk) | TL-31
ITEM #: TL-31_Size-02
PRICE: $18.45 Regular priceThe deerhoof and the Rondin are the ultimate striping brushes- no taping needed! A deerhoof is designed for striping color or size, much like the rondin brush. The deerhoof shape offers a distinct slant, which allows for optimum surface contact. The deerhoof is best for applying size or color to flat or curved surfaces. In order to make this brush so dense, its ferrule is constructed by hand, with quill and wire. By pinching the brush at the heal, long and exact stripes can be achieved.
| SIZE | BRUSH LENGTH | FERRULE WIDTH | FERRULE LENGTH |
HAIR LENGTH |
| 2 | 6.9" / 17.4cm | |||
| 4 | 7" / 17.9cm | |||
| 6 | ||||
| 8 | 7.3" / 18.6cm | |||
| 10 |
7.4" / 18.8cm |
|
HAIR TYPE |
Skunk |
|
BRUSH HOLD |
Choked Pen Hold |
|
USAGE |
Painting freehand stripes or applying size |
|
MEDIUM |
Water or Oil |
|
FERRULE |
Wire-tied quill |
|
HANDLE |
Wooden round short |
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
PRO Pointed Glazing Brush (Bristle, Nylon) | GLZ-41
ITEM #: GLZ-41_Size-000
PRICE: $14.45 Regular priceOur PRO SERIES POINTED glazing (sash) brushes have a classic round shape for ultimate paint medium dispersion. It is used to apply glaze, paint, wax, and thin textures. Use like a standard paint brush or scrubbing motion.
| SIZE | BRUSH LENGTH | FERRULE WIDTH | HAIR LENGTH |
| 000 | 11.6" / 29.4cm | .4" / 11mm | 2.2" / 56mm |
| 0 | 11.7" / 29.8cm | .8 / 20mm | 2.4" / 62mm |
| 2 | 12.2" / 31cm | .9" / 22mm | 2.8" / 70mm |
| 4 | 12.7" / 32.2cm | 1" / 26mm | 3" / 75mm |
| 6 | 13.4" / 34cm | 1.2" / 31mm | 3.3" / 84mm |
| 8 | 13.5" / 34.4cm | 1.3" / 34mm | 3.5" / 89mm |
|
HAIR TYPE |
Natural Bristle / Nylon blend |
|
USAGE |
Application of varnish, paint, glaze medium |
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
PRO Domed Glazing Brush (Bluetop) | GLZ-34
ITEM #: GLZ-34_Size-02
PRICE: $16.75 Regular priceOur BLUETOP PRO SERIES DOMED glazing (sash) brushes have a classic round shape for ultimate paint medium dispersion. It is used to apply glaze, paint, wax, and thin textures. Use like a standard paint brush or scrubbing motion.
| SIZE | BRUSH LENGTH | FERRULE WIDTH | HAIR LENGTH |
| 2 | 12" / 30.5cm | .86" / 22mm | 2.5" / 64mm |
| 4 | 12.3" / 31.2cm | 1" / 26mm | 2.5" / 64mm |
| 6 | 12.9" / 32.8cm | 1.2" / 29mm | 2.8" / 72mm |
| 8 | 13.3" / 33.8cm | 1.3" / 33mm | 3.1" / 78mm |
|
HAIR TYPE |
Bluetop synthetic fiber |
|
USAGE |
Application of varnish, paint, glaze medium; stippling |
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
Long Liner Brush (Samina Nylon) | TL-15
ITEM #: TL-15_Size-04
PRICE: $11.55 Regular priceThis brush is indispensable for all your ornamentation work. This lining brush is made with soft samina hair and has exceptional performance for fine veined and breche marble. Samina fiber is meant to simulate squirrel hair, but with the capability to transport all of today's water mediums. Available in 4 sizes.
|
SIZE
|
BRUSH LENGTH
|
FERRULE WIDTH
|
FERRULE LENGTH
|
HAIR LENGTH
|
|
2
|
12" / 30.5cm |
" / mm
|
" / mm
|
" / mm
|
|
4
|
12.4" / 31.5cm |
" / mm
|
" / mm
|
" / mm
|
|
6
|
12.4" / 30.6cm |
" / mm
|
" / mm
|
" / mm
|
|
8
|
12" / 30.5cm |
|
|
|
|
HAIR TYPE
|
Samina
|
|
BRUSH HOLD
|
Conductor's Hold, Pencil Hold
|
|
USAGE
|
Fine veining for faux marble in water mediums; fissures
|
|
MEDIUM
|
Water
|
|
FERRULE
|
Tin
|
|
HANDLE
|
Wooden round long
|
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
Original Stubby Spalter Brush (Nylon, Bristle) | GLZ-07D
ITEM #: GLZ-07D_Size-040
PRICE: $6.09 Regular price Regularly: $10.15 Sale price Save $4.06The spalter is one of the most used tools in our decorative brush kit. Unlike the average chip brush, our spalter has a thick row (1/3 inch) of short hair that is densely packed with a bristle/nylon blend for ultimate performance and control for today's water mediums. The smaller sizes have a variety of uses, from basecoats to final glazing, 'stretching' to softening. Available in 6 sizes.
Most of our large and fine hair brushes are hand-set and made with different hairs that are tapped in a small copper cylinder before being glued into the ferrule. This is why some of the hairs are not properly affixed to the ferrule, so the brush will shed some hair the first few times you will use it.
Thick hair: examples are; badger, hog (china bristle), horse hair
Fine hair: examples are sable; squirrel, goat, skunk (fine, thin short hair)
Synthetic Fiber: examples are; taklon, samina, bordeaux, synthetic bristle
To minimize brush shedding, you should:
All acrylic glazes contain some sort of ammonia which attacks the structure of the natural hair. Therefore, brush maintenance and thorough repetitive cleaning as described in step 1, 2, & 3 is imperative to protect and extend the life of your brush.
Applying a few drops of ‘leave in’ conditioner is also a good idea if you’re not going to be using your brush for some time.
Dried Paint: If some acrylic glaze becomes hardened on the brush, start by removing the heaviest part with denatured alcohol then rinse with water and coat the hairs with Murphy’s Oil Soap and leave for several hours. Apply the steps again from 1, 2, & 3 so the paint will brush out easily and leave your brush as good as new. Be careful as soap left too long in the natural hair will deteriorate the flexibility of the hair.
| Oil Medium | Water Medium | |
|---|---|---|
| Large Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Wash brush with warm water and a lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry upside down. | Rinse thoroughly with warm water. Clean with a tiny bit of lathering soap and rinse until completely clean. Shake out excess water, quickly form brush shape, and then allow to dry. |
| Small Brushes | Prep brushes by thinning in two or more baths of spirits or until a rag runs free of paint. Apply a generous portion of Lard to the tip of the brush and store. To reuse brush, completely thin with spirits. | Clean each small brush very carefully and gently with a tiny bit of lathering soap. Shake out excess water, quickly form brush shape, and then allow to dry . To reshape a brush, dip it in Gum Arabic. |
Wire-Tied Veining Brush (Bristle) MB-02
ITEM #: MB-02_Size-02
PRICE: $10.40 Regular price